Refine
Year of publication
Document Type
- Conference Proceeding (22)
- Article (8)
- Part of a Book (1)
Language
- English (31) (remove)
Keywords
- Abrasive grain material (1)
- Actuators (1)
- Additive manufacturing (1)
- Aquaculture (1)
- Austenitic stainless steels (1)
- Corrosion Resistance (1)
- Corrosion resistance (1)
- Duplex stainless steel (1)
- Dynamic testing plant (1)
- Dynamic tests (1)
The evolution of strain induced martensite in austenitic stainless steel AISI 304 was investigated in a rolling contact on a two-discs-tribometer. The effects of surface roughness, slip and normal force as well as the number of load cycles were examined. In comparison to the investigations of martensitic phase transformation during cold rolling, the applied stresses are considerably lower. The formation of strain induced martensite was detected in-situ by means of a FERITSCOPE MP30 and ex-situ by optical microscopy after etching with Kane etchant. Both number of load cycles and magnitude of normal force appeared to be the main influencing factors regarding strain induced martensitic evolution in low stress rolling contacts.
In the automotive industry a strong effort has been undertaken to reduce the weight of modern vehicles. In order to reduce the energy consumption and to improve the environmental sustainability, the importance of weight reduction activities is even growing faster. As lightweight designing is becoming more and more expensive and show less potential savings, new approaches are needed. One promising technology could be the use of shape memory elements. In the last years a lot of potential application possibilities were presented, demonstrating the benefit of these functional elements in automotive design solutions: they often reduce complexity, weight and design space of an actuation device and enable new functions. In addition they work silently and are therefore ideally suitable for comfort applications in the passenger cabin. Because of the current trend to electric vehicle the hitherto existing drawback of a high electrical energy consumption of shape memory actuators in some design proposals is not given any more.
Pitting susceptibility of metastable austenitic stainless steels as a function of surface conditions
(2019)
The influence of surface roughness and local defects on pitting susceptibility of type 304 (UNS S30400) and type 301 (UNS S30100) in chloride solution were investigated. Because the mechanical properties can be regarded as decisive for the achieved surface quality, different properties of the base material were obtained by cold rolling the metastable austenites. This was done before the surfaces were finished. Therefor the surfaces were treated by different grinding parameters to generate different surface conditions and different defects. As a reference, different standardised surface finishes were used.
By using and comparing different methods for the characterization of surface roughness and surface texture, it is possible to find a relationship between the quantity and characteristics of local defects on the one hand and pitting susceptibility on the other hand. For the machining parameters used, a ranking of the influencing factors on the corrosion resistance achieved could be determined.
The automated application of software-based solutions for estimating the pitting susceptibility of machined surfaces and components will be discussed using concrete examples.
This paper presents the current state of development and selected technological challenges in the application of ecologically and economically sustainable nets for aquaculture based on ongoing development projects. These aim at the development of a new material system of high-strength stainless steel wires as net material with environmentally compatible antifouling properties for nearshore and offshore aquacultures. Current plastic netting materials will be replaced with high-strength stainless steel to provide a more environmentally friendly system that can withstand more severe mechanical stresses (waves, storms, tides and predators). A new antifouling strategy is expected to solve current challenges, such as ecological damage (e.g., due to pollution from copper-containing antifouling substances or microplastics), high maintenance costs (e.g., cleaning and repairs), and shorter service life. Approaches for the next development steps are presented based on previous experience as well as calculation models based on this experience.
Magnetic effects on austenitic stainless steels, formed during a low temperature carburizing depending on the alloy composition are discussed in this paper. Samples of different austenitic stainless steel alloys have been subjected to a multiple low-temperature carburization. Layer characteriszation with light microscope and hardness profiles show a growth of the layer thickness. The formation of an expanded austenite layer (lattice expansion) could be detected by X-ray diffraction (XRD). Feritscope was used to determine the magnetizability, whereby not all austenitic alloys form a magnetizability after treatment. Furthermore, test procedures were developed to visualize the magnetizability. For this purpose, magnetic force microscope measurements and investigations with ferrofluid were carried out and a fir tree ferromagnetic layer strucure could be proven.
Thermochemical surface hardening is used to overcome the weak mechanical performance of austenitic and duplex stainless steels. Both low-temperature carburizing and nitrocarburizing can improve the hardness, wear, galling, and cavitation resistance, while maintaining their good corrosion resistance. Therefore, it is crucial to not form chromium-rich precipitates during hardening as these can deteriorate the passivity of the alloy. The hardening parameters, the chemical composition of the steel, and the manufacturing route of a component determine whether precipitates are formed. This article gives an overview of suitable alloys for low-temperature surface hardening and the performance under corrosive loading.
In automotive a lot of electromagnetically, pyrotechnically or mechanically driven actuators are integrated to run comfort systems and to control safety systems in modern passenger cars. Using shape memory alloys (SMA) the existing systems could be simplified, performing the same function through new mechanisms with reduced size, weight, and costs. A drawback for the use of SMA in safety systems is the lack of materials knowledge concerning the durability of the switching function (long-time stability of the shape memory effect). Pedestrian safety systems play a significant role to reduce injuries and fatal casualties caused by accidents. One automotive safety system for pedestrian protection is the bonnet lifting system. Based on such an application, this article gives an introduction to existing bonnet lifting systems for pedestrian protection, describes the use of quick changing shape memory actuators and the results of the study concerning the long-time stability of the tested NiTi-wires. These wires were trained, exposed up to 4years at elevated temperatures (up to 140°C) and tested regarding their phase change temperatures, times, and strokes. For example, it was found that A P-temperature is shifted toward higher temperatures with longer exposing periods and higher temperatures. However, in the functional testing plant a delay in the switching time could not be detected. This article gives some answers concerning the long-time stability of NiTi-wires that were missing till now. With this knowledge, the number of future automotive applications using SMA can be increased. It can be concluded, that the use of quick changing shape memory actuators in safety systems could simplify the mechanism, reduce maintenance and manufacturing costs and should be insertable also for other automotive applications.
Investigation of magnetic effects on austenitic stainless steels after low temperature carburization
(2018)
This work aims at investigating the magnetic effects of austenitc stainless steels which can occur after a low temperature carburisation depending on the alloy. Samples were prepared of different alloys and subjected to a multiple low temperature carburisation to obtain different treatment conditions for each alloy. The layer characterisation was carried out by light microscope and also by hardening profiles and shows that the layer develops with each additional treatment cycle. A lattice expansion could be detected in all treated samples by X-ray diffraction. Magnetisability was measured using Feritscope and SQUID measurements. Not all alloys showed magnetisability after treatment. In addition to MFM measurements, experiments with Ferrofluid were also used to visualize the magnetic areas. These studies show that only about half of the formed layer becomes magnetisable and has a domain-like structure.
Ferromagnetism is of increasing importance in the growing field of electromobility and data storage. In stable austenitic steels, the occurrence of ferromagnetism is not expected and would also interfere with many applications. However, ferromagnetism in austenitic stainless steels after low-temperature nitriding has already been shown in the past. Herein, the presence of ferromagnetism in austenitic steels is discovered after low-temperature carburization (Kolsterizing), which represents a novel and unique finding. A zone of expanded austenite is established on various austenitic stainless steels by low-temperature carburization and the respective ferromagnetism is investigated in relation to the alloy composition. The ferromagnetism occurring is determined by means of a commercial magnetoinductive sensor (Feritscope). Ferromagnetic domains are visualized by magnetic force microscopy and a ferrofluid. X-ray diffraction measurements indicate a clear difference in the lattice expansion of the different alloys. Furthermore, a different appearance of the magnetizable microstructure regions (magnetic domain structure) is detected depending on the grain orientation determined by electron backscatter diffraction (EBSD). Strongly pronounced magnetic domains show no linear lattice defects, whereas in small magnetizable areas linear lattice defects are detected by electron channeling contrast imaging and EBSD.
Thermal shape memory alloys show extraordinary material properties and can be used as actuators, dampers and sensors. Since their discovery in the middle of the last century they have been investigated and further developed. The majority of the industrial applications with the highest material sales can still be found in the medical industry, where they are used due to their superelastic and thermal shape memory effect, e.g. as stents or as guidewires and tools in the minimal invasive surgery. Particularly in recent years, more and more applications have been developed for other industrial fields, e.g. for the household goods, civil engineering and automotive sector. In this context it is worth mentioning that for the latter sector, million seller series applications have found their way into some European automobile manufacturers. The German VDI guideline for shape memory alloys introduced in 2017 will give the material a further boost in application. Last but not least the new production technologies of additive manufacturing with metal laser sintering plants open up additional applications for these multifunctional materials. This paper gives an overview of the extraordinary material properties of shape memory components, shows examples of different applications and discusses European trends against the background of the most recent standard and new production technologies.