Adjusting the friction response of the wheel-rail interface is a key factor in the mitigation of wear and rollingcontact fatigue (RCF) in rails. The use of top-of-rail (TOR) friction conditioners has the potential to reduce maintenance costs significantly. Unfortunately, conflicting results on the use of commercial TOR conditioners have been presented in the literature. In this work, the performance of commercial TOR conditioners and a laboratory-made formulation were tested, both on the lab scale and in field measurements. Friction results are discussed together with the structural and chemical analysis of the tested materials.
Einfluss der Oberfläche
(2018)
Poster
Pitting susceptibility of metastable austenitic stainless steels as a function of surface conditions
(2019)
Fachvortrag auf der 10th International European Stainless Steel Conference and 6th European Duplex Stainless Steel Conference (ESSC & DUPLEX 2019), 30.09. – 02.10.2019, Vienna, Austria
Fachvortrag auf dem Swiss Tribology Symposium, 12.11.2019, Hightechzentrum Aargau, Brugg, Schweiz
The electrochemical behavior for different surface conditions and different degrees of deformation of metastable austenitic stainless steel AISI 304 UNS S30400 were studied using critical pitting potential and electrochemical noise measurements. The influence on corrosion resistance by using different abrasives (silicon carbide and corundum) for surface finish by grinding is illustrated. For the characterization of local defects and surface topography, scanning electron microscopy (SEM) and tactile measurements were used. An inverse correlation between occurrence of local defects on the surface and critical pitting potential was found by using image processing. Therefore, gray scale values of different surfaces were compared. The influence of mass content of α'-martensite on the corrosion resistance is shown by comparing different qualities of surface finish. For smooth machined surfaces it can be shown that an increasing numbers of strain induced martensite is decreasing the corrosion resistance lightly. For low abrasive machining an inverse correlation between the critical pitting potential and surface roughness is given. However, for higher abrasive machining parameters, this correlation could not be found.
Pitting susceptibility of metastable austenitic stainless steels as a function of surface conditions
(2019)
The influence of surface roughness and local defects on pitting susceptibility of type 304 (UNS S30400) and type 301 (UNS S30100) in chloride solution were investigated. Because the mechanical properties can be regarded as decisive for the achieved surface quality, different properties of the base material were obtained by cold rolling the metastable austenites. This was done before the surfaces were finished. Therefor the surfaces were treated by different grinding parameters to generate different surface conditions and different defects. As a reference, different standardised surface finishes were used.
By using and comparing different methods for the characterization of surface roughness and surface texture, it is possible to find a relationship between the quantity and characteristics of local defects on the one hand and pitting susceptibility on the other hand. For the machining parameters used, a ranking of the influencing factors on the corrosion resistance achieved could be determined.
The automated application of software-based solutions for estimating the pitting susceptibility of machined surfaces and components will be discussed using concrete examples.
Durch Beanspruchungen bei der Fertigung oder in der Anwendung können metastabile austenitische Stähle eine Phasenumwandlung von ?- Austenit zu ?‘-Martensit durchlaufen. Verbunden damit sind Eigenschaftsänderungen, welche sich signifikant auf das Werkstoffverhalten unter mechanischer, tribologischer oder korrosiver Belastung auswirken können.
Um möglichen negativen Auswirkungen wie ungewollte Magnetisierbarkeit oder Beeinflussung von Fertigungsparameter sowie Korrosionseigenschaften zu unterbinden muss die martensitische Phase zunächst erfasst und quantifiziert werden.
Für diese Aufgabe stehen neben den bekannten und kostenintensiven Verfahren wie EBSD und XRD für die praxisnahe Anwendung das magneto-induktive Messverfahren und verschiedene Ätzmethoden zur Verfügung.
Anhand von Applikationen aus Anwendung, Fertigung und Forschung werden die Wirkweisen, Vorteile und Grenzen verschiedener Ätzverfahren und dem magneto-induktiv messenden FERITSCOPE® MP30 aufgezeigt. Ebenso werden ergänzende Methoden bzw. Techniken zur Validation der Verfahren diskutiert und erläutert.
This paper compares the surface morphology of differently finished austenitic stainless steel AISI 316L, also in combination with low temperature carburization. Milled and tumbled surfaces were analyzed by means of corrosion resistance and surface morphology. The results of potentiodynamic measurements show that professional grinding operations with SiC and Al2O3 always lead to a better corrosion resistance of low temperature carburized surfaces compared to the untreated reference in the used acidified chloride solution. Big influence on the corrosion resistance of vibratory ground or tumbled surfaces has the amount of plastic deformation while machining, that has to be kept low for austenitic stainless steels. Due to the high ductility, plastic deformation can lead to the formation of meta stable pits that can be initiation points of corrosion. The formation of meta stable pits can be aggravated by low temperature diffusion processes.