Multi-object tracking filters require a birth density to detect new objects from measurement data. If the initial positions of new objects are unknown, it may be useful to choose an adaptive birth density. In this paper, a circular birth density is proposed, which is placed like a band around the surveillance area. This allows for 360° coverage. The birth density is described in polar coordinates and considers all point-symmetric quantities such as radius, radial velocity and tangential velocity of objects entering the surveillance area. Since it is assumed that these quantities are unknown and may vary between different targets, detected trajectories, and in particular their initial states, are used to estimate the distribution of initial states. The adapted birth density is approximated as a Gaussian mixture, so that it can be used for filters operating on Cartesian coordinates.
This paper describes the development of a control system for an industrial heating application. In this process a moving substrate is passing through a heating zone with variable speed. Heat is applied by hot air to the substrate with the air flow rate being the manipulated variable. The aim is to control the substrate’s temperature at a specific location after passing the heating zone. First, a model is derived for a point attached to the moving substrate. This is modified to reflect the temperature of the moving substrate at the specified location. In order to regulate the temperature a nonlinear model predictive control approach is applied using an implicit Euler scheme to integrate the model and an augmented gradient based optimization approach. The performance of the controller has been validated both by simulations and experiments on the physical plant. The respective results are presented in this paper.
Trajectory Tracking of a Fully-actuated Surface Vessel using Nonlinear Model Predictive Control
(2021)
The trajectory tracking problem for a fully-actuated real-scaled surface vessel is addressed in this paper. The unknown hydrodynamic and propulsion parameters of the vessel’s dynamic model were identified using an experimental maneuver-based identification process. Then, a nonlinear model predictive control (NMPC) scheme is designed and the controller’s performance is assessed through the variation of NMPC parameters and constraints tightening for tracking a curved trajectory.
In this paper, a systematic comparison of three different advanced control strategies for automated docking of a vessel is presented. The controllers are automatically tuned offline by applying an optimization process using simulations of the whole system including trajectory planner and state and disturbance observer. Then investigations are conducted subject to performance and robustness using Monte Carlos simulation with varying model parameters and disturbances. The control strategies have also been tested in full scale experiments using the solar research vessel Solgenia. The investigated control strategies all have demonstrated very good performance in both, simulation and real world experiments. Videos are available under https://www.htwg-konstanz.de/forschung-und-transfer/institute-und-labore/isd/regelungstechnik/videos/
In multi-extended object tracking, parameters (e.g., extent) and trajectory are often determined independently. In this paper, we propose a joint parameter and trajectory (JPT) state and its integration into the Bayesian framework. This allows processing measurements that contain information about parameters and states. Examples of such measurements are bounding boxes given from an image processing algorithm. It is shown that this approach can consider correlations between states and parameters. In this paper, we present the JPT Bernoulli filter. Since parameters and state elements are considered in the weighting of the measurement data assignment hypotheses, the performance is higher than with the conventional Bernoulli filter. The JPT approach can be also used for other Bayes filters.
In this paper, a novel measurement model based on spherical double Fourier series (DFS) for estimating the 3D shape of a target concurrently with its kinematic state is introduced. Here, the shape is represented as a star-convex radial function, decomposed as spherical DFS. In comparison to ordinary DFS, spherical DFS do not suffer from ambiguities at the poles. Details will be given in the paper. The shape representation is integrated into a Bayesian state estimator framework via a measurement equation. As range sensors only generate measurements from the target side facing the sensor, the shape representation is modified to enable application of shape symmetries during the estimation process. The model is analyzed in simulations and compared to a shape estimation procedure using spherical harmonics. Finally, shape estimation using spherical and ordinary DFS is compared to analyze the effect of the pole problem in extended object tracking (EOT) scenarios.
Modeling a suitable birth density is a challenge when using Bernoulli filters such as the Labeled Multi-Bernoulli (LMB) filter. The birth density of newborn targets is unknown in most applications, but must be given as a prior to the filter. Usually the birth density stays unchanged or is designed based on the measurements from previous time steps.
In this paper, we assume that the true initial state of new objects is normally distributed. The expected value and covariance of the underlying density are unknown parameters. Using the estimated multi-object state of the LMB and the Rauch-Tung-Striebel (RTS) recursion, these parameters are recursively estimated and adapted after a target is detected.
The main contribution of this paper is an algorithm to estimate the parameters of the birth density and its integration into the LMB framework. Monte Carlo simulations are used to evaluate the detection driven adaptive birth density in two scenarios. The approach can also be applied to filters that are able to estimate trajectories.
Flatness-based feed-forward control of solenoid actuators is considered. For precise motion planning and accurate steering of conventional solenoids, eddy currents cannot be neglected. The system of ordinary differential equations including eddy currents, that describes the nonlinear dynamics of such actuators, is not differentially flat. Thus, a distributed parameter approach based on a diffusion equation is considered, that enables the parametrization of the eddy current by the armature position and its time derivatives. In order to design the feedforward control, the distributed parameter model of the eddy current subsystem is combined with a typical nonlinear lumped parameter model for the electrical and mechanical subsystems of the solenoid. The control design and its application are illustrated by numerical and practical results for an industrial solenoid actuator.
Extracting suitable features from acquired data to accurately depict the current health state of a system is crucial in data driven condition monitoring and prediction. Usually, analogue sensor data is sampled at rates far exceeding the Nyquist-rate containing substantial amounts of redundancies and noise, imposing high computational loads due to the subsequent and necessary feature processing chain (generation, dimensionality reduction, rating and selection). To overcome these problems, Compressed Sensing can be used to sample directly to a compressed space, provided the signal at hand and the employed compression/measurement system meet certain criteria. Theory states, that during this compression step enough information is conserved, such that a reconstruction of the original signal is possible with high probability. The proposed approach however does not rely on reconstructed data for condition monitoring purposes, but uses directly the compressed signal representation as feature vector. It is hence assumed that enough information is conveyed by the compression for condition monitoring purposes. To fuse the compressed coefficients into one health index that can be used as input for remaining useful life prediction algorithms and is limited to a reasonable range between 1 and 0, a logistic regression approach is used. Run-to-failure data of three translational electromagnetic actuators is used to demonstrate the health index generation procedure. A comparison to the time domain ground truth signals obtained from Nyquist sampled coil current measurements shows reasonable agreement. I.e. underlying wear-out phenomena can be reproduced by the proposed approach enabling further investigation of the application of prognostic methods.
This paper presents a new likelihood-based partitioning method of the measurement set for the extended object probability hypothesis density (PHD) filter framework. Recent work has mostly relied on heuristic partitioning methods that cluster the measurement data based on a distance measure between the single measurements. This can lead to poor filter performance if the tracked extended objects are closely spaced. The proposed method called Stochastic Partitioning (StP) is based on sampling methods and was inspired by a former work of Granström et. al. In this work, the StP method is applied to a Gaussian inverse Wishart (GIW) PHD filter and compared to a second filter implementation that uses the heuristic Distance Partitioning (DP) method. The performance is evaluated in Monte Carlo simulations in a scenario where two objects approach each other. It is shown that the sampling based StP method leads to an improved filter performance compared to DP.