Refine
Document Type
- Conference Proceeding (26)
- Article (5)
- Other Publications (2)
- Part of a Book (1)
- Doctoral Thesis (1)
Has Fulltext
- no (35)
Keywords
- Abrasive grain material (1)
- Anhaftung (1)
- Aquaculture (1)
- Behälterbau (1)
- Corrosion Resistance (1)
- Duplex stainless steel (1)
- Edelstahl Rostfrei (1)
- Expanded austenite layer (1)
- Fish farming (1)
- Geological protection (1)
Poster
Low temperature carburizing of a series of austenitic stainless with various combinations of chromium and nickel equivalents was performed. The investigation of the response towards low temperature carburized for three stainless steels with various Cr- and Ni-equivalents showed that the carbon uptake depends significantly on the chemical composition of the base material. The higher carbon content in the expanded austenite layer of specimen 6 (1.4565) and specimen 4 (1.4539/AISI 904L) compared to specimen 2 (1.4404/AISI 316L) is assumed to be mainly related to the difference in the specimens’ chromium content. More chromium leads to more lattice expansion. Along with the higher carbon content, higher hardness values and higher compressive residual stresses in the expanded austenite zone are introduced than for low temperature carburized AISI 316L. The residual stresses obtained from X-ray diffraction lattice strain investigation depend strongly on the chosen X-ray elastic constants. Presently, no values are known for carbon (or nitrogen) stabilized expanded austenite. Nevertheless, first principle elastic constants for γ′&minus Fe4C appear to provide realistic residual stress values. Magnetic force microscopy and measurement with an eddy current probe indicate that austenitic stainless steels can become ferromagnetic upon carburizing, similar for low temperature nitriding. The apparent transition from para- to ferromagnetism cannot be attributed entirely to the interstitially dissolved carbon content in the formed expanded austenite layer but appears to depend also on the metallic composition of the alloy, in particular the Ni content.
The corrosion resistance of stainless steels is massively influenced by the condition of their surface. The surface quality includes the topography of the surface, the structure and composition of the passive layer, and the surface near structure of the base material. These factors are influenced by final physical/chemical surface treatments. The presented work shows significantly lower corrosion resistance for mechanical machined specimens than for etched specimens. It also turns out that the rougher the surface, the lower the corrosion resistance gets. However, there is no general finding which shows if blasted or grinded surfaces are more appropriate, but a dependency on process parameters and the characteristics on corrosive exposure in terms of corrosion behavior. The results show that not only the surface roughness Ra has an influence on corrosion behavior but also the shape of peaks and valleys which are evolved by surface treatments. Imperfections in the base material, like sulfidic inclusions lead to a weaker passive layer, respectively, to a decrease of the corrosion resistance. By using special passivating techniques the corrosion resistance of stainless steels can be increased to a higher level in comparison to common passivation.
This paper compares the surface morphology of differently finished austenitic stainless steel AISI 316L, also in combination with low temperature carburization. Milled and tumbled surfaces were analyzed by means of corrosion resistance and surface morphology. The results of potentiodynamic measurements show that professional grinding operations with SiC and Al2O3 always lead to a better corrosion resistance of low temperature carburized surfaces compared to the untreated reference in the used acidified chloride solution. Big influence on the corrosion resistance of vibratory ground or tumbled surfaces has the amount of plastic deformation while machining, that has to be kept low for austenitic stainless steels. Due to the high ductility, plastic deformation can lead to the formation of meta stable pits that can be initiation points of corrosion. The formation of meta stable pits can be aggravated by low temperature diffusion processes.
Hot isostatic pressing (HIP) allows the production of complex components geometry. Generally, a high quality of the components is achieved due to the well managed composition of the metal powder and the non-isotropic properties. If a duplex stainless steel is produced, a heat treatment after the HIP-process is necessary to remove precipitations like carbides, nitrides and intermetallic phases. In a new process, the sintering step should be combined with the heat treatment. In this case a high cooling rate is necessary to avoid precipitations in duplex stainless steels. In this work, the influence of the HIP-temperature and the wall thickness on corrosion resistance, microstructure and impact strength were investigated. The results should help to optimize the process parameters like temperature and cooling rate. For the investigation, two HIP-temperatures were tested in a classical HIP-process step with a defined cooling rate. An additional heat treatment was not conducted. The specimens were cut from different sectors of the HIP-block. For investigation of the corrosion resistance, the critical pitting temperature was determined with electrochemical method according to EN ISO 17864. An impact test was used to determine the impact transition temperature. Metallographic investigations show the microstructure in the different sectors of the HIP-block.