Institut für Systemdynamik - ISD
The trajectory tracking problem for a real-scaled fully-actuated surface vessel is addressed in this paper. A nonlinear model predictive control (NMPC) scheme was designed to track a reference trajectory, considering state and input constraints, and environmental disturbances, which were assumed to be constant over the prediction horizon. The controller was tested by performing docking maneuvers using the real-scaled research vessel from the University of Applied Sciences Konstanz at the Rhine river in Germany. A comparison between the experimental results and the simulated ones was analyzed to validate the NMPC controller.
Trajectory Tracking of a Fully-actuated Surface Vessel using Nonlinear Model Predictive Control
(2021)
The trajectory tracking problem for a fully-actuated real-scaled surface vessel is addressed in this paper. The unknown hydrodynamic and propulsion parameters of the vessel’s dynamic model were identified using an experimental maneuver-based identification process. Then, a nonlinear model predictive control (NMPC) scheme is designed and the controller’s performance is assessed through the variation of NMPC parameters and constraints tightening for tracking a curved trajectory.
This paper presents the integration of a spline based extension model into a probability hypothesis density (PHD) filter for extended targets. Using this filter the position and extension of each object as well as the number of present objects can jointly be estimated. Therefore, the spline extension model and the PHD filter are addressed and merged in a Gaussian mixture (GM) implementation. Simulation results using artificial laser measurements are used to evaluate the performance of the presented filter. Finally, the results are illustrated and discussed.
Virtual measurement models (VMM) can be used to generate artificial measurements and emulate complex sensor models such as Lidar. The input of the VMM is an estimation and the output is the set of measurements this estimation would cause. A Kalman filter with extension estimation based on random matrices is used to filter mean and covariance of the real measurements. If these match the mean and covariance of the artificial measurements, then the given estimation is appropriate. The optimal input of the VMM is found using an adaptation algorithm. In this paper, the VMM approach is expanded for multi-extended object tracking where objects can be occluded and are only partially visible. The occlusion can be compensated if the extension estimation is performed for all objects together. The VMM now receives as input an estimation for the multi-object state and the output are the measurements that this multi-object state would cause.
This paper presents the swinging up and stabilization control of a Furuta pendulum using the recently published nonlinear Model Predictive Path Integral (MPPI) approach. This algorithm is based on a path integral over stochastic trajectories and can be parallelized easily. The controller parameters are tuned offline regarding the nonlinear system dynamics and simulations. Constraints in terms of state and input are taken into account in the cost function. The presented approach sequentially computes an optimal control sequence that minimizes this optimal control problem online. The control strategy has been tested in full-scale experiments using a pendulum prototype. The investigated MPPI controller has demonstrated excellent performance in simulation for the swinging up and stabilizing task. In order to also achieve outstanding performance in a real-world experiment using a controller with limited computing power, a linear quadratic controller (LQR) is designed for the stabilization task. In this paper, the determination of the controller parameters for the MPPI algorithm is described in detail. Further, a discussion treats the advantages of the nonlinear MPPI control.
This paper presents a new likelihood-based partitioning method of the measurement set for the extended object probability hypothesis density (PHD) filter framework. Recent work has mostly relied on heuristic partitioning methods that cluster the measurement data based on a distance measure between the single measurements. This can lead to poor filter performance if the tracked extended objects are closely spaced. The proposed method called Stochastic Partitioning (StP) is based on sampling methods and was inspired by a former work of Granström et. al. In this work, the StP method is applied to a Gaussian inverse Wishart (GIW) PHD filter and compared to a second filter implementation that uses the heuristic Distance Partitioning (DP) method. The performance is evaluated in Monte Carlo simulations in a scenario where two objects approach each other. It is shown that the sampling based StP method leads to an improved filter performance compared to DP.
Soft-input decoding of concatenated codes based on the Plotkin construction and BCH component codes
(2020)
Low latency communication requires soft-input decoding of binary block codes with small to medium block lengths.
In this work, we consider generalized multiple concatenated (GMC) codes based on the Plotkin construction. These codes are similar to Reed-Muller (RM) codes. In contrast to RM codes, BCH codes are employed as component codes. This leads to improved code parameters. Moreover, a decoding algorithm is proposed that exploits the recursive structure of the concatenation. This algorithm enables efficient soft-input decoding of binary block codes with small to medium lengths. The proposed codes and their decoding achieve significant performance gains compared with RM codes and recursive GMC decoding.
Side Channel Attack Resistance of the Elliptic Curve Point Multiplication using Gaussian Integers
(2020)
Elliptic curve cryptography is a cornerstone of embedded security. However, hardware implementations of the elliptic curve point multiplication are prone to side channel attacks. In this work, we present a new key expansion algorithm which improves the resistance against timing and simple power analysis attacks. Furthermore, we consider a new concept for calculating the point multiplication, where the points of the curve are represented as Gaussian integers. Gaussian integers are subset of the complex numbers, such that the real and imaginary parts are integers. Since Gaussian integer fields are isomorphic to prime fields, this concept is suitable for many elliptic curves. Representing the key by a Gaussian integer expansion is beneficial to reduce the computational complexity and the memory requirements of a secure hardware implementation.
Side Channel Attack Resistance of the Elliptic Curve Point Multiplication using Eisenstein Integers
(2020)
Asymmetric cryptography empowers secure key exchange and digital signatures for message authentication. Nevertheless, consumer electronics and embedded systems often rely on symmetric cryptosystems because asymmetric cryptosystems are computationally intensive. Besides, implementations of cryptosystems are prone to side-channel attacks (SCA). Consequently, the secure and efficient implementation of asymmetric cryptography on resource-constrained systems is demanding. In this work, elliptic curve cryptography is considered. A new concept for an SCA resistant calculation of the elliptic curve point multiplication over Eisenstein integers is presented and an efficient arithmetic over Eisenstein integers is proposed. Representing the key by Eisenstein integer expansions is beneficial to reduce the computational complexity and the memory requirements of an SCA protected implementation.
In the past years, algorithms for 3D shape tracking using radial functions in spherical coordinates represented with different methods have been proposed. However, we have seen that mainly measurements from the lateral surface of the target can be expected in a lot of dynamic scenarios and only few measurements from the top and bottom parts leading to an error-prone shape estimate in the top and bottom regions when using a representation in spherical coordinates. We, therefore, propose to represent the shape of the target using a radial function in cylindrical coordinates, as these only represent regions of the lateral surface, and no information from the top or bottom parts is needed. In this paper, we use a Fourier-Chebyshev double series for 3D shape representation since a mixture of Fourier and Chebyshev series is a suitable basis for expanding a radial function in cylindrical coordinates. We investigate the method in a simulated and real-world maritime scenario with a CAD model of the target boat as a reference. We have found that shape representation in cylindrical coordinates has decisive advantages compared to a shape representation in spherical coordinates and should preferably be used if no prior knowledge of the measurement distribution on the surface of the target is available.
In this paper, a novel measurement model based on spherical double Fourier series (DFS) for estimating the 3D shape of a target concurrently with its kinematic state is introduced. Here, the shape is represented as a star-convex radial function, decomposed as spherical DFS. In comparison to ordinary DFS, spherical DFS do not suffer from ambiguities at the poles. Details will be given in the paper. The shape representation is integrated into a Bayesian state estimator framework via a measurement equation. As range sensors only generate measurements from the target side facing the sensor, the shape representation is modified to enable application of shape symmetries during the estimation process. The model is analyzed in simulations and compared to a shape estimation procedure using spherical harmonics. Finally, shape estimation using spherical and ordinary DFS is compared to analyze the effect of the pole problem in extended object tracking (EOT) scenarios.
The introduction of multi level cell (MLC) and triple level cell (TLC) technologies reduced the reliability of flash memories significantly compared with single level cell (SLC) flash. The reliability of the flash memory suffers from various errors causes. Program/erase cycles, read disturb, and cell to cell interference impact the threshold voltages. With pre-defined fixed read thresholds a voltage shift increases the bit error rate (BER). This work proposes a read threshold calibration method that aims on minimizing the BER by adapting the read voltages. The adaptation of the read thresholds is based on the number of errors observed in the codeword protecting a small amount of meta-data. Simulations based on flash measurements demonstrate that this method can significantly reduce the BER of TLC memories.
In 3D extended object tracking (EOT), well-established models exist for tracking the object extent using various shape priors. A single update, however, has to be performed for every measurement using these models leading to a high computational runtime for high-resolution sensors. In this paper, we address this problem by using various model-independent downsampling schemes based on distance heuristics and random sampling as pre-processing before the update. We investigate the methods in a simulated and real-world tracking scenario using two different measurement models with measurements gathered from a LiDAR sensor. We found that there is a huge potential for speeding up 3D EOT by dropping up to 95\% of the measurements in our investigated scenarios when using random sampling. Since random sampling, however, can also result in a subset that does not represent the total set very well, leading to a poor tracking performance, there is still a high demand for further research.
Analysing observability is an important step in the
process of designing state feedback controllers. While for linear
systems observability has been widely studied and easy-to-check
necessary and sufficient conditions are available, for nonlinear
systems, such a general recipe does not exist and different classes
of systems require different techniques. In this paper, we analyse
observability for an industrial heating process where a stripe-
shaped plastic workpiece is moving through a heating zone where
it is heated up to a specific temperature by applying hot air to its
surface through a nozzle. A modeling approach for this process
is briefly presented, yielding a nonlinear Ordinary Differential
Equation model. Sensitivity-based observability analysis is used
to identify unobservable states and make suggestions for addi-
tional sensor locations. In practice, however, it is not possible
to place additional sensors, so the available measurements are
used to implement a simple open-loop state estimator with
offset compensation and numerical and experimental results are
presented.
Large persistent memory is crucial for many applications in embedded systems and automotive computing like AI databases, ADAS, and cutting-edge infotainment systems. Such applications require reliable NAND flash memories made for harsh automotive conditions. However, due to high memory densities and production tolerances, the error probability of NAND flash memories has risen. As the number of program/erase cycles and the data retention times increase, non-volatile NAND flash memories' performance and dependability suffer. The read reference voltages of the flash cells vary due to these aging processes. In this work, we consider the issue of reference voltage adaption. The considered estimation procedure uses shallow neural networks to estimate the read reference voltages for different life-cycle conditions with the help of histogram measurements. We demonstrate that the training data for the neural networks can be enhanced by using shifted histograms, i.e., a training of the neural networks is possible based on a few measurements of some extreme points used as training data. The trained neural networks generalize well for other life-cycle conditions.
This paper focuses on the multivariable control of a drawing tower process. The nature of the process together with the differences in measurement noise levels that affect the variables to be controlled motivated the development of a new MPC algorithm. An extension of a multivariable predictive control algorithm with separated prediction horizons is proposed. The obtained experimental results show the usefulness of the proposed algorithm..
This work introduces new signal constellations based on Eisenstein integers, i.e., the hexagonal lattice. These sets of Eisenstein integers have a cardinality which is an integer power of three. They are proposed as signal constellations for representation in the equivalent complex baseband model, especially for applications like physical-layer network coding or MIMO transmission where the constellation is required to be a subset of a lattice. It is shown that these constellations form additive groups where the addition over the complex plane corresponds to the addition with carry over ternary Galois fields. A ternary set partitioning is derived that enables multilevel coding based on ternary error-correcting codes. In the subsets, this partitioning achieves a gain of 4.77 dB, which results from an increased minimum squared Euclidean distance of the signal points. Furthermore, the constellation-constrained capacities over the AWGN channel and the related level capacities in case of ternary multilevel coding are investigated. Simulation results for multilevel coding based on ternary LDPC codes are presented which show that a performance close to the constellation-constrained capacities can be achieved.
Recently published nonlinear model-based control
approaches achieve impressive performances in complex real-
world applications. However, due to model-plant mismatches
and unforeseen disturbances, the model-based controller’s per-
formance is limited in full-scale applications. In most applica-
tions, low-level control loops mitigate the model-plant mismatch
and the sensitivity to disturbances. But what is the influence
of these low-level control loops? In this paper, we present
the model predictive path integral (MPPI) control of a self-
balancing vehicle and investigate the influence of subordinate
control loops on closed-loop performance. Therefore, simulation
and full-scale experiments are performed and analyzed. Subor-
dinate control loops empower the MPPI controller because they
dampen the influence of disturbances, and thus improve the
model’s accuracy. This is the basis for the successful application
of model-based control approaches in real-world systems. All
in all, a model is used to design a low-level controller, then
its closed-loop behavior is determined, and this model is used
within the superimposed MPPI control loop – modeling for
control and vice versa.
The Montgomery multiplication is an efficient method for modular arithmetic. Typically, it is used for modular arithmetic over integer rings to prevent the expensive inversion for the modulo reduction. In this work, we consider modular arithmetic over rings of Gaussian integers. Gaussian integers are subset of the complex numbers such that the real and imaginary parts are integers. In many cases Gaussian integer rings are isomorphic to ordinary integer rings. We demonstrate that the concept of the Montgomery multiplication can be extended to Gaussian integers. Due to independent calculation of the real and imaginary parts, the computation complexity of the multiplication is reduced compared with ordinary integer modular arithmetic. This concept is suitable for coding applications as well as for asymmetric key cryptographic systems, such as elliptic curve cryptography or the Rivest-Shamir-Adleman system.
This paper describes the development of a control system for an industrial heating application. In this process a moving substrate is passing through a heating zone with variable speed. Heat is applied by hot air to the substrate with the air flow rate being the manipulated variable. The aim is to control the substrate’s temperature at a specific location after passing the heating zone. First, a model is derived for a point attached to the moving substrate. This is modified to reflect the temperature of the moving substrate at the specified location. In order to regulate the temperature a nonlinear model predictive control approach is applied using an implicit Euler scheme to integrate the model and an augmented gradient based optimization approach. The performance of the controller has been validated both by simulations and experiments on the physical plant. The respective results are presented in this paper.