In this paper, a gain-scheduled nonlinear control structure is proposed for a surface vessel, which takes advantage of extended linearisation techniques. Thereby, an accurate tracking of desired trajectories can be guaranteed that contributes to a safe and reliable water transport. The PI state feedback control is extended by a feedforward control based on an inverse system model. To achieve an accurate trajectory tracking, however, an observer-based disturbance compensation is necessary: external disturbances by cross currents or wind forces in lateral direction and wave-induced measurement disturbances are estimated by a nonlinear observer and used for a compensation. The efficiency and the achieved tracking performance are shown by simulation results using a validated model of the ship Korona at the HTWG Konstanz, Germany. Here, both tracking behaviour and rejection of disturbance forces in lateral direction are considered.
This paper presents the integration of a spline based extension model into a probability hypothesis density (PHD) filter for extended targets. Using this filter the position and extension of each object as well as the number of present objects can jointly be estimated. Therefore, the spline extension model and the PHD filter are addressed and merged in a Gaussian mixture (GM) implementation. Simulation results using artificial laser measurements are used to evaluate the performance of the presented filter. Finally, the results are illustrated and discussed.
In 3D extended object tracking (EOT), well-established models exist for tracking the object extent using various shape priors. A single update, however, has to be performed for every measurement using these models leading to a high computational runtime for high-resolution sensors. In this paper, we address this problem by using various model-independent downsampling schemes based on distance heuristics and random sampling as pre-processing before the update. We investigate the methods in a simulated and real-world tracking scenario using two different measurement models with measurements gathered from a LiDAR sensor. We found that there is a huge potential for speeding up 3D EOT by dropping up to 95\% of the measurements in our investigated scenarios when using random sampling. Since random sampling, however, can also result in a subset that does not represent the total set very well, leading to a poor tracking performance, there is still a high demand for further research.
With the high resolution of modern sensors such as multilayer LiDARs, estimating the 3D shape in an extended object tracking procedure is possible. In recent years, 3D shapes have been estimated in spherical coordinates using Gaussian processes, spherical double Fourier series or spherical harmonics. However, observations have shown that in many scenarios only a few measurements are obtained from top or bottom surfaces, leading to error-prone estimates in spherical coordinates. Therefore, in this paper we propose to estimate the shape in cylindrical coordinates instead, applying harmonic functions. Specifically, we derive an expansion for 3D shapes in cylindrical coordinates by solving a boundary value problem for the Laplace equation. This shape representation is then integrated in a plain greedy association model and compared to shape estimation procedures in spherical coordinates. Since the shape representation is only integrated in a basic estimator, the results are preliminary and a detailed discussion for future work is presented at the end of the paper.
In this paper, a novel measurement model based on spherical double Fourier series (DFS) for estimating the 3D shape of a target concurrently with its kinematic state is introduced. Here, the shape is represented as a star-convex radial function, decomposed as spherical DFS. In comparison to ordinary DFS, spherical DFS do not suffer from ambiguities at the poles. Details will be given in the paper. The shape representation is integrated into a Bayesian state estimator framework via a measurement equation. As range sensors only generate measurements from the target side facing the sensor, the shape representation is modified to enable application of shape symmetries during the estimation process. The model is analyzed in simulations and compared to a shape estimation procedure using spherical harmonics. Finally, shape estimation using spherical and ordinary DFS is compared to analyze the effect of the pole problem in extended object tracking (EOT) scenarios.
In this paper, approximating the shape of a sailing boat using elliptic cones is investigated. Measurements are assumed to be gathered from the target's surface recorded by 3D scanning devices such as multilayer LiDAR sensors. Therefore, different models for estimating the sailing boat's extent are presented and evaluated in simulated and real-world scenarios. In particular, the measurement source association problem is addressed in the models. Simulated investigations are conducted with a static and a moving elliptic cone. The real-world scenario was recorded with a Velodyne Alpha Prime (VLP-128) mounted on a ferry of Lake Constance. Final results of this paper constitute the extent estimation of a single sailing boat using LiDAR data applying various measurement models.
In the past years, algorithms for 3D shape tracking using radial functions in spherical coordinates represented with different methods have been proposed. However, we have seen that mainly measurements from the lateral surface of the target can be expected in a lot of dynamic scenarios and only few measurements from the top and bottom parts leading to an error-prone shape estimate in the top and bottom regions when using a representation in spherical coordinates. We, therefore, propose to represent the shape of the target using a radial function in cylindrical coordinates, as these only represent regions of the lateral surface, and no information from the top or bottom parts is needed. In this paper, we use a Fourier-Chebyshev double series for 3D shape representation since a mixture of Fourier and Chebyshev series is a suitable basis for expanding a radial function in cylindrical coordinates. We investigate the method in a simulated and real-world maritime scenario with a CAD model of the target boat as a reference. We have found that shape representation in cylindrical coordinates has decisive advantages compared to a shape representation in spherical coordinates and should preferably be used if no prior knowledge of the measurement distribution on the surface of the target is available.
The improvement of collision avoidance for vessels in close range encounter situations is an important topic for maritime traffic safety. Typical approaches generate evasive trajectories or optimise the trajectories of all involved vessels. Such a collision avoidance system has to produce evasive manoeuvres that do not confuse other navigators. To achieve this behaviour, a probabilistic obstacle handling based on information from a radar sensor with target tracking, that considers measurement and tracking uncertainties is proposed. A grid based path search algorithm, that takes the information from the probabilistic obstacle handling into account, is then used to generate evasive trajectories. The proposed algorithms have been tested and verified in a simulated environment for inland waters.
Motion safety for vessels
(2015)
The improvement of collision avoidance for vessels in close range encounter situations is an important topic for maritime traffic safety. Typical approaches generate evasive trajectories or optimise the trajectories of all involved vessels. The idea of this work is to validate these trajectories related to guaranteed motion safety, which means that it is not sufficient for a trajectory to be collision-free, but it must additionally ensure that an evasive manoeuvre is performable at any time. An approach using the distance and the evolution of the distance to the other vessels is proposed. The concept of Inevitable Collision States (ICS) is adopted to identify the states for which no evasive manoeuvre exist. Furthermore, it is implemented into a collision avoidance system for recreational crafts to demonstrate the performance.
Observer-based self sensing for digital (on–off) single-coil solenoid valves is investigated. Self sensing refers to the case where merely the driving signals used to energize the actuator (voltage and coil current) are available to obtain estimates of both the position and velocity. A novel observer approach for estimating the position and velocity from the driving signals is presented, where the dynamics of the mechanical subsystem can be neglected in the model. Both the effect of eddy currents and saturation effects are taken into account in the observer model. Practical experimental results are shown and the new method is compared with a full-order sliding mode observer.
The method of signal injection is investigated for position estimation of proportional solenoid valves. A simple observer is proposed to estimate a position-dependent parameter, i.e. the eddy current resistance, from which the position is calculated analytically. Therefore, the relationship of position and impedance in the case of sinusoidal excitation is accurately described by consideration of classical electrodynamics. The observer approach is compared with a standard identification method, and evaluated by practical experiments on an off-the-shelf proportional solenoid valve.
Flatness-based feed-forward control of solenoid actuators is considered. For precise motion planning and accurate steering of conventional solenoids, eddy currents cannot be neglected. The system of ordinary differential equations including eddy currents, that describes the nonlinear dynamics of such actuators, is not differentially flat. Thus, a distributed parameter approach based on a diffusion equation is considered, that enables the parametrization of the eddy current by the armature position and its time derivatives. In order to design the feedforward control, the distributed parameter model of the eddy current subsystem is combined with a typical nonlinear lumped parameter model for the electrical and mechanical subsystems of the solenoid. The control design and its application are illustrated by numerical and practical results for an industrial solenoid actuator.
Knowing the position of the spool in a solenoid valve, without using costly position sensors, is of considerable interest in a lot of industrial applications. In this paper, the problem of position estimation based on state observers for fast-switching solenoids, with sole use of simple voltage and current measurements, is investigated. Due to the short spool traveling time in fast-switching valves, convergence of the observer errors has to be achieved very fast. Moreover, the observer has to be robust against modeling uncertainties and parameter variations. Therefore, different state observer approaches are investigated, and compared to each other regarding possible uncertainties. The investigation covers a High-Gain-Observer approach, a combined High-Gain Sliding-Mode-Observer approach, both based on extended linearization, and a nonlinear Sliding-Mode-Observer based on equivalent output injection. The results are discussed by means of numerical simulations for all approaches, and finally physical experiments on a valve-mock-up are thoroughly discussed for the nonlinear Sliding-Mode-Observer.
A semilinear distributed parameter approach for solenoid valve control including saturation effects
(2015)
In this paper a semilinear parabolic PDE for the control of solenoid valves is presented. The distributed parameter model of the cylinder becomes nonlinear by the inclusion of saturation effects due to the material's B/H-curve. A flatness based solution of the semilinear PDE is shown as well as a convergence proof of its series solution. By numerical simulation results the adaptability of the approach is demonstrated, and differences between the linear and the nonlinear case are discussed. The major contribution of this paper is the inclusion of saturation effects into the magnetic field governing linear diffusion equation, and the development of a flatness based solution for the resulting semilinear PDE as an extension of previous works [1] and [2].
This paper presents a new likelihood-based partitioning method of the measurement set for the extended object probability hypothesis density (PHD) filter framework. Recent work has mostly relied on heuristic partitioning methods that cluster the measurement data based on a distance measure between the single measurements. This can lead to poor filter performance if the tracked extended objects are closely spaced. The proposed method called Stochastic Partitioning (StP) is based on sampling methods and was inspired by a former work of Granström et. al. In this work, the StP method is applied to a Gaussian inverse Wishart (GIW) PHD filter and compared to a second filter implementation that uses the heuristic Distance Partitioning (DP) method. The performance is evaluated in Monte Carlo simulations in a scenario where two objects approach each other. It is shown that the sampling based StP method leads to an improved filter performance compared to DP.
This paper focuses on the multivariable control of a drawing tower process. The nature of the process together with the differences in measurement noise levels that affect the variables to be controlled motivated the development of a new MPC algorithm. An extension of a multivariable predictive control algorithm with separated prediction horizons is proposed. The obtained experimental results show the usefulness of the proposed algorithm..
Multi-object tracking filters require a birth density to detect new objects from measurement data. If the initial positions of new objects are unknown, it may be useful to choose an adaptive birth density. In this paper, a circular birth density is proposed, which is placed like a band around the surveillance area. This allows for 360° coverage. The birth density is described in polar coordinates and considers all point-symmetric quantities such as radius, radial velocity and tangential velocity of objects entering the surveillance area. Since it is assumed that these quantities are unknown and may vary between different targets, detected trajectories, and in particular their initial states, are used to estimate the distribution of initial states. The adapted birth density is approximated as a Gaussian mixture, so that it can be used for filters operating on Cartesian coordinates.