Refine
Document Type
- Conference Proceeding (32)
- Article (8)
- Report (1)
Keywords
Institute
- Institut für Systemdynamik - ISD (41) (remove)
The trajectory tracking problem for a real-scaled fully-actuated surface vessel is addressed in this paper. A nonlinear model predictive control (NMPC) scheme was designed to track a reference trajectory, considering state and input constraints, and environmental disturbances, which were assumed to be constant over the prediction horizon. The controller was tested by performing docking maneuvers using the real-scaled research vessel from the University of Applied Sciences Konstanz at the Rhine river in Germany. A comparison between the experimental results and the simulated ones was analyzed to validate the NMPC controller.
Trajectory Tracking of a Fully-actuated Surface Vessel using Nonlinear Model Predictive Control
(2021)
The trajectory tracking problem for a fully-actuated real-scaled surface vessel is addressed in this paper. The unknown hydrodynamic and propulsion parameters of the vessel’s dynamic model were identified using an experimental maneuver-based identification process. Then, a nonlinear model predictive control (NMPC) scheme is designed and the controller’s performance is assessed through the variation of NMPC parameters and constraints tightening for tracking a curved trajectory.
This paper presents the integration of a spline based extension model into a probability hypothesis density (PHD) filter for extended targets. Using this filter the position and extension of each object as well as the number of present objects can jointly be estimated. Therefore, the spline extension model and the PHD filter are addressed and merged in a Gaussian mixture (GM) implementation. Simulation results using artificial laser measurements are used to evaluate the performance of the presented filter. Finally, the results are illustrated and discussed.
Virtual measurement models (VMM) can be used to generate artificial measurements and emulate complex sensor models such as Lidar. The input of the VMM is an estimation and the output is the set of measurements this estimation would cause. A Kalman filter with extension estimation based on random matrices is used to filter mean and covariance of the real measurements. If these match the mean and covariance of the artificial measurements, then the given estimation is appropriate. The optimal input of the VMM is found using an adaptation algorithm. In this paper, the VMM approach is expanded for multi-extended object tracking where objects can be occluded and are only partially visible. The occlusion can be compensated if the extension estimation is performed for all objects together. The VMM now receives as input an estimation for the multi-object state and the output are the measurements that this multi-object state would cause.
This paper presents the swinging up and stabilization control of a Furuta pendulum using the recently published nonlinear Model Predictive Path Integral (MPPI) approach. This algorithm is based on a path integral over stochastic trajectories and can be parallelized easily. The controller parameters are tuned offline regarding the nonlinear system dynamics and simulations. Constraints in terms of state and input are taken into account in the cost function. The presented approach sequentially computes an optimal control sequence that minimizes this optimal control problem online. The control strategy has been tested in full-scale experiments using a pendulum prototype. The investigated MPPI controller has demonstrated excellent performance in simulation for the swinging up and stabilizing task. In order to also achieve outstanding performance in a real-world experiment using a controller with limited computing power, a linear quadratic controller (LQR) is designed for the stabilization task. In this paper, the determination of the controller parameters for the MPPI algorithm is described in detail. Further, a discussion treats the advantages of the nonlinear MPPI control.
This paper presents a new likelihood-based partitioning method of the measurement set for the extended object probability hypothesis density (PHD) filter framework. Recent work has mostly relied on heuristic partitioning methods that cluster the measurement data based on a distance measure between the single measurements. This can lead to poor filter performance if the tracked extended objects are closely spaced. The proposed method called Stochastic Partitioning (StP) is based on sampling methods and was inspired by a former work of Granström et. al. In this work, the StP method is applied to a Gaussian inverse Wishart (GIW) PHD filter and compared to a second filter implementation that uses the heuristic Distance Partitioning (DP) method. The performance is evaluated in Monte Carlo simulations in a scenario where two objects approach each other. It is shown that the sampling based StP method leads to an improved filter performance compared to DP.
In the past years, algorithms for 3D shape tracking using radial functions in spherical coordinates represented with different methods have been proposed. However, we have seen that mainly measurements from the lateral surface of the target can be expected in a lot of dynamic scenarios and only few measurements from the top and bottom parts leading to an error-prone shape estimate in the top and bottom regions when using a representation in spherical coordinates. We, therefore, propose to represent the shape of the target using a radial function in cylindrical coordinates, as these only represent regions of the lateral surface, and no information from the top or bottom parts is needed. In this paper, we use a Fourier-Chebyshev double series for 3D shape representation since a mixture of Fourier and Chebyshev series is a suitable basis for expanding a radial function in cylindrical coordinates. We investigate the method in a simulated and real-world maritime scenario with a CAD model of the target boat as a reference. We have found that shape representation in cylindrical coordinates has decisive advantages compared to a shape representation in spherical coordinates and should preferably be used if no prior knowledge of the measurement distribution on the surface of the target is available.
In this paper, a novel measurement model based on spherical double Fourier series (DFS) for estimating the 3D shape of a target concurrently with its kinematic state is introduced. Here, the shape is represented as a star-convex radial function, decomposed as spherical DFS. In comparison to ordinary DFS, spherical DFS do not suffer from ambiguities at the poles. Details will be given in the paper. The shape representation is integrated into a Bayesian state estimator framework via a measurement equation. As range sensors only generate measurements from the target side facing the sensor, the shape representation is modified to enable application of shape symmetries during the estimation process. The model is analyzed in simulations and compared to a shape estimation procedure using spherical harmonics. Finally, shape estimation using spherical and ordinary DFS is compared to analyze the effect of the pole problem in extended object tracking (EOT) scenarios.
Reliability Assessment of an Unscented Kalman Filter by Using Ellipsoidal Enclosure Techniques
(2022)
The Unscented Kalman Filter (UKF) is widely used for the state, disturbance, and parameter estimation of nonlinear dynamic systems, for which both process and measurement uncertainties are represented in a probabilistic form. Although the UKF can often be shown to be more reliable for nonlinear processes than the linearization-based Extended Kalman Filter (EKF) due to the enhanced approximation capabilities of its underlying probability distribution, it is not a priori obvious whether its strategy for selecting sigma points is sufficiently accurate to handle nonlinearities in the system dynamics and output equations. Such inaccuracies may arise for sufficiently strong nonlinearities in combination with large state, disturbance, and parameter covariances. Then, computationally more demanding approaches such as particle filters or the representation of (multi-modal) probability densities with the help of (Gaussian) mixture representations are possible ways to resolve this issue. To detect cases in a systematic manner that are not reliably handled by a standard EKF or UKF, this paper proposes the computation of outer bounds for state domains that are compatible with a certain percentage of confidence under the assumption of normally distributed states with the help of a set-based ellipsoidal calculus. The practical applicability of this approach is demonstrated for the estimation of state variables and parameters for the nonlinear dynamics of an unmanned surface vessel (USV).
In 3D extended object tracking (EOT), well-established models exist for tracking the object extent using various shape priors. A single update, however, has to be performed for every measurement using these models leading to a high computational runtime for high-resolution sensors. In this paper, we address this problem by using various model-independent downsampling schemes based on distance heuristics and random sampling as pre-processing before the update. We investigate the methods in a simulated and real-world tracking scenario using two different measurement models with measurements gathered from a LiDAR sensor. We found that there is a huge potential for speeding up 3D EOT by dropping up to 95\% of the measurements in our investigated scenarios when using random sampling. Since random sampling, however, can also result in a subset that does not represent the total set very well, leading to a poor tracking performance, there is still a high demand for further research.
A constructive nonlinear observer design for self-sensing of digital (ON/OFF) single coil electromagnetic actuators is studied. Self-sensing in this context means that solely the available energizing signals, i.e., coil current and driving voltage are used to estimate the position and velocity trajectories of the moving plunger. A nonlinear sliding mode observer is considered, where the stability of the reduced error dynamics is analyzed by the equivalent control method. No simplifications are made regarding magnetic saturation and eddy currents in the underlying dynamical model. The observer gains are constructed by taking into account some generic properties of the systems nonlinearities. Two possible choices of the observer gains are discussed. Furthermore, an observer-based tracking control scheme to achieve sensorless soft landing is considered and its closed-loop stability is studied. Experimental results for observer-based soft landing of a fast-switching solenoid valve under dry conditions are presented to demonstrate the usefulness of the approach.
Analysing observability is an important step in the
process of designing state feedback controllers. While for linear
systems observability has been widely studied and easy-to-check
necessary and sufficient conditions are available, for nonlinear
systems, such a general recipe does not exist and different classes
of systems require different techniques. In this paper, we analyse
observability for an industrial heating process where a stripe-
shaped plastic workpiece is moving through a heating zone where
it is heated up to a specific temperature by applying hot air to its
surface through a nozzle. A modeling approach for this process
is briefly presented, yielding a nonlinear Ordinary Differential
Equation model. Sensitivity-based observability analysis is used
to identify unobservable states and make suggestions for addi-
tional sensor locations. In practice, however, it is not possible
to place additional sensors, so the available measurements are
used to implement a simple open-loop state estimator with
offset compensation and numerical and experimental results are
presented.
A nonlinear mathematical model for the dynamics of permanent magnet synchronous machines with interior magnets is discussed. The model of the current dynamics captures saturation and dependency on the rotor angle. Based on the model, a flatness-based field-oriented closed-loop controller and a feed-forward compensation of torque ripples are derived. Effectiveness and robustness of the proposed algorithms are demonstrated by simulation results.
This paper focuses on the multivariable control of a drawing tower process. The nature of the process together with the differences in measurement noise levels that affect the variables to be controlled motivated the development of a new MPC algorithm. An extension of a multivariable predictive control algorithm with separated prediction horizons is proposed. The obtained experimental results show the usefulness of the proposed algorithm..
Recently published nonlinear model-based control
approaches achieve impressive performances in complex real-
world applications. However, due to model-plant mismatches
and unforeseen disturbances, the model-based controller’s per-
formance is limited in full-scale applications. In most applica-
tions, low-level control loops mitigate the model-plant mismatch
and the sensitivity to disturbances. But what is the influence
of these low-level control loops? In this paper, we present
the model predictive path integral (MPPI) control of a self-
balancing vehicle and investigate the influence of subordinate
control loops on closed-loop performance. Therefore, simulation
and full-scale experiments are performed and analyzed. Subor-
dinate control loops empower the MPPI controller because they
dampen the influence of disturbances, and thus improve the
model’s accuracy. This is the basis for the successful application
of model-based control approaches in real-world systems. All
in all, a model is used to design a low-level controller, then
its closed-loop behavior is determined, and this model is used
within the superimposed MPPI control loop – modeling for
control and vice versa.
This paper describes the development of a control system for an industrial heating application. In this process a moving substrate is passing through a heating zone with variable speed. Heat is applied by hot air to the substrate with the air flow rate being the manipulated variable. The aim is to control the substrate’s temperature at a specific location after passing the heating zone. First, a model is derived for a point attached to the moving substrate. This is modified to reflect the temperature of the moving substrate at the specified location. In order to regulate the temperature a nonlinear model predictive control approach is applied using an implicit Euler scheme to integrate the model and an augmented gradient based optimization approach. The performance of the controller has been validated both by simulations and experiments on the physical plant. The respective results are presented in this paper.
In multi-extended object tracking, parameters (e.g., extent) and trajectory are often determined independently. In this paper, we propose a joint parameter and trajectory (JPT) state and its integration into the Bayesian framework. This allows processing measurements that contain information about parameters and states. Examples of such measurements are bounding boxes given from an image processing algorithm. It is shown that this approach can consider correlations between states and parameters. In this paper, we present the JPT Bernoulli filter. Since parameters and state elements are considered in the weighting of the measurement data assignment hypotheses, the performance is higher than with the conventional Bernoulli filter. The JPT approach can be also used for other Bayes filters.
Extracting suitable features from acquired data to accurately depict the current health state of a system is crucial in data driven condition monitoring and prediction. Usually, analogue sensor data is sampled at rates far exceeding the Nyquist-rate containing substantial amounts of redundancies and noise, imposing high computational loads due to the subsequent and necessary feature processing chain (generation, dimensionality reduction, rating and selection). To overcome these problems, Compressed Sensing can be used to sample directly to a compressed space, provided the signal at hand and the employed compression/measurement system meet certain criteria. Theory states, that during this compression step enough information is conserved, such that a reconstruction of the original signal is possible with high probability. The proposed approach however does not rely on reconstructed data for condition monitoring purposes, but uses directly the compressed signal representation as feature vector. It is hence assumed that enough information is conveyed by the compression for condition monitoring purposes. To fuse the compressed coefficients into one health index that can be used as input for remaining useful life prediction algorithms and is limited to a reasonable range between 1 and 0, a logistic regression approach is used. Run-to-failure data of three translational electromagnetic actuators is used to demonstrate the health index generation procedure. A comparison to the time domain ground truth signals obtained from Nyquist sampled coil current measurements shows reasonable agreement. I.e. underlying wear-out phenomena can be reproduced by the proposed approach enabling further investigation of the application of prognostic methods.
With the high resolution of modern sensors such as multilayer LiDARs, estimating the 3D shape in an extended object tracking procedure is possible. In recent years, 3D shapes have been estimated in spherical coordinates using Gaussian processes, spherical double Fourier series or spherical harmonics. However, observations have shown that in many scenarios only a few measurements are obtained from top or bottom surfaces, leading to error-prone estimates in spherical coordinates. Therefore, in this paper we propose to estimate the shape in cylindrical coordinates instead, applying harmonic functions. Specifically, we derive an expansion for 3D shapes in cylindrical coordinates by solving a boundary value problem for the Laplace equation. This shape representation is then integrated in a plain greedy association model and compared to shape estimation procedures in spherical coordinates. Since the shape representation is only integrated in a basic estimator, the results are preliminary and a detailed discussion for future work is presented at the end of the paper.