Refine
Document Type
- Conference Proceeding (64)
- Article (27)
- Doctoral Thesis (8)
- Master's Thesis (2)
- Patent (1)
- Report (1)
Keywords
Institute
- Institut für Systemdynamik - ISD (103) (remove)
This work studies a wind noise reduction approach for communication applications in a car environment. An endfire array consisting of two microphones is considered as a substitute for an ordinary cardioid microphone capsule of the same size. Using the decomposition of the multichannel Wiener filter (MWF), a suitable beamformer and a single-channel post filter are derived. Due to the known array geometry and the location of the speech source, assumptions about the signal properties can be made to simplify the MWF beamformer and to estimate the speech and noise power spectral densities required for the post filter. Even for closely spaced microphones, the different signal properties at the microphones can be exploited to achieve a significant reduction of wind noise. The proposed beamformer approach results in an improved speech signal regarding the signal-to-noise-ratio and keeps the linear speech distortion low. The derived post filter shows equal performance compared to known approaches but reduces the effort for noise estimation.
The trajectory tracking problem for a real-scaled fully-actuated surface vessel is addressed in this paper. A nonlinear model predictive control (NMPC) scheme was designed to track a reference trajectory, considering state and input constraints, and environmental disturbances, which were assumed to be constant over the prediction horizon. The controller was tested by performing docking maneuvers using the real-scaled research vessel from the University of Applied Sciences Konstanz at the Rhine river in Germany. A comparison between the experimental results and the simulated ones was analyzed to validate the NMPC controller.
Trajectory Tracking of a Fully-actuated Surface Vessel using Nonlinear Model Predictive Control
(2021)
The trajectory tracking problem for a fully-actuated real-scaled surface vessel is addressed in this paper. The unknown hydrodynamic and propulsion parameters of the vessel’s dynamic model were identified using an experimental maneuver-based identification process. Then, a nonlinear model predictive control (NMPC) scheme is designed and the controller’s performance is assessed through the variation of NMPC parameters and constraints tightening for tracking a curved trajectory.
This paper presents the integration of a spline based extension model into a probability hypothesis density (PHD) filter for extended targets. Using this filter the position and extension of each object as well as the number of present objects can jointly be estimated. Therefore, the spline extension model and the PHD filter are addressed and merged in a Gaussian mixture (GM) implementation. Simulation results using artificial laser measurements are used to evaluate the performance of the presented filter. Finally, the results are illustrated and discussed.
In the field of autonomously driving vehicles the environment perception containing dynamic objects like other road users is essential. Especially, detecting other vehicles in the road traffic using sensor data is of utmost importance. As the sensor data and the applied system model for the objects of interest are noise corrupted, a filter algorithm must be used to track moving objects. Using LIDAR sensors one object gives rise to more than one measurement per time step and is therefore called extended object. This allows to jointly estimate the objects, position, as well as its orientation, extension and shape. Estimating an arbitrary shaped object comes with a higher computational effort than estimating the shape of an object that can be approximated using a basic geometrical shape like an ellipse or a rectangle. In the case of a vehicle, assuming a rectangular shape is an accurate assumption.
A recently developed approach models the contour of a vehicle as periodic B-spline function. This representation is an easy to use tool, as the contour can be specified by some basis points in Cartesian coordinates. Also rotating, scaling and moving the contour is easy to handle using a spline contour. This contour model can be used to develop a measurement model for extended objects, that can be integrated into a tracking filter. Another approach modeling the shape of a vehicle is the so-called bounding box that represents the shape as rectangle.
In this thesis the basics of single, multi and extended object tracking, as well as the basics of B-spline functions are addressed. Afterwards, the spline measurement model is established in detail and integrated into an extended Kalman filter to track a single extended object. An implementation of the resulting algorithm is compared with the rectangular shape estimator. The implementation of the rectangular shape estimator is provided. The comparison is done using long-term considerations with Monte Carlo simulations and by analyzing the results of a single run. Therefore, both algorithms are applied to the same measurements. The measurements are generated using an artificial LIDAR sensor in a simulation environment.
In a real-world tracking scenario detecting several extended objects and measurements that do not originate from a real object, named clutter measurements, is possible. Also, the sudden appearance and disappearance of an object is possible. A filter framework investigated in recent years that can handle tracking multiple objects in a cluttered environment is a random finite set based approach. The idea of random finite sets and its use in a tracking filter is recapped in this thesis. Afterwards, the spline measurement model is included in a multi extended object tracking framework. An implementation of the resulting filter is investigated in a long-term consideration using Monte Carlo simulations and by analyzing the results of a single run. The multi extended object filter is also applied to artificial LIDAR measurements generated in a simulation environment.
The results of comparing the spline based and rectangular based extended object trackers show a more stable performance of the spline extended object tracker. Also, some problems that have to be addressed in future works are discussed. The investigation of the resulting multi extended object tracker shows a successful integration of the spline measurement model in a multi extended object tracker. Also, with these results some problems remain, that have to be solved in future works.
Virtual measurement models (VMM) can be used to generate artificial measurements and emulate complex sensor models such as Lidar. The input of the VMM is an estimation and the output is the set of measurements this estimation would cause. A Kalman filter with extension estimation based on random matrices is used to filter mean and covariance of the real measurements. If these match the mean and covariance of the artificial measurements, then the given estimation is appropriate. The optimal input of the VMM is found using an adaptation algorithm. In this paper, the VMM approach is expanded for multi-extended object tracking where objects can be occluded and are only partially visible. The occlusion can be compensated if the extension estimation is performed for all objects together. The VMM now receives as input an estimation for the multi-object state and the output are the measurements that this multi-object state would cause.
This paper presents the swinging up and stabilization control of a Furuta pendulum using the recently published nonlinear Model Predictive Path Integral (MPPI) approach. This algorithm is based on a path integral over stochastic trajectories and can be parallelized easily. The controller parameters are tuned offline regarding the nonlinear system dynamics and simulations. Constraints in terms of state and input are taken into account in the cost function. The presented approach sequentially computes an optimal control sequence that minimizes this optimal control problem online. The control strategy has been tested in full-scale experiments using a pendulum prototype. The investigated MPPI controller has demonstrated excellent performance in simulation for the swinging up and stabilizing task. In order to also achieve outstanding performance in a real-world experiment using a controller with limited computing power, a linear quadratic controller (LQR) is designed for the stabilization task. In this paper, the determination of the controller parameters for the MPPI algorithm is described in detail. Further, a discussion treats the advantages of the nonlinear MPPI control.
This paper presents a new likelihood-based partitioning method of the measurement set for the extended object probability hypothesis density (PHD) filter framework. Recent work has mostly relied on heuristic partitioning methods that cluster the measurement data based on a distance measure between the single measurements. This can lead to poor filter performance if the tracked extended objects are closely spaced. The proposed method called Stochastic Partitioning (StP) is based on sampling methods and was inspired by a former work of Granström et. al. In this work, the StP method is applied to a Gaussian inverse Wishart (GIW) PHD filter and compared to a second filter implementation that uses the heuristic Distance Partitioning (DP) method. The performance is evaluated in Monte Carlo simulations in a scenario where two objects approach each other. It is shown that the sampling based StP method leads to an improved filter performance compared to DP.
Soft-input decoding of concatenated codes based on the Plotkin construction and BCH component codes
(2020)
Low latency communication requires soft-input decoding of binary block codes with small to medium block lengths.
In this work, we consider generalized multiple concatenated (GMC) codes based on the Plotkin construction. These codes are similar to Reed-Muller (RM) codes. In contrast to RM codes, BCH codes are employed as component codes. This leads to improved code parameters. Moreover, a decoding algorithm is proposed that exploits the recursive structure of the concatenation. This algorithm enables efficient soft-input decoding of binary block codes with small to medium lengths. The proposed codes and their decoding achieve significant performance gains compared with RM codes and recursive GMC decoding.
Error correction coding based on soft-input decoding can significantly improve the reliability of non-volatile flash memories. This work proposes a soft-input decoder for generalized concatenated (GC) codes. GC codes are well suited for error correction in flash memories for high reliability data storage. We propose GC codes constructed from inner extended binary Bose-Chaudhuri-Hocquenghem (BCH) codes and outer Reed-Solomon codes. The extended BCH codes enable an efficient hard-input decoding. Furthermore, a low-complexity soft-input decoding method is proposed. This bit-flipping decoder uses a fixed number of test patterns and an algebraic decoder for soft-decoding. An acceptance criterion for the final candidate codeword is proposed. Combined with error and erasure decoding of the outer Reed-Solomon codes, this acceptance criterion can improve the decoding performance and reduce the decoding complexity. The presented simulation results show that the proposed bit-flipping decoder in combination with outer error and erasure decoding can outperform maximum likelihood decoding of the inner codes.