Refine
Year of publication
- 2018 (88) (remove)
Document Type
- Conference Proceeding (88) (remove)
Keywords
Institute
- Fakultät Bauingenieurwesen (1)
- Fakultät Informatik (13)
- Fakultät Maschinenbau (3)
- Fakultät Wirtschafts-, Kultur- und Rechtswissenschaften (2)
- Institut für Angewandte Forschung - IAF (3)
- Institut für Optische Systeme - IOS (9)
- Institut für Strategische Innovation und Technologiemanagement - IST (5)
- Institut für Systemdynamik - ISD (6)
- Institut für professionelles Schreiben - IPS (2)
- Konstanz Institut für Corporate Governance - KICG (2)
- Konstanzer Institut für Prozesssteuerung - KIPS (2)
Generalized concatenated (GC) codes with soft-input decoding were recently proposed for error correction in flash memories. This work proposes a soft-input decoder for GC codes that is based on a low-complexity bit-flipping procedure. This bit-flipping decoder uses a fixed number of test patterns and an algebraic decoder for soft-input decoding. An acceptance criterion for the final candidate codeword is proposed. Combined with error and erasure decoding of the outer Reed-Solomon codes, this bit-flipping decoder can improve the decoding performance and reduce the decoding complexity compared to the previously proposed sequential decoding. The bit-flipping decoder achieves a decoding performance similar to a maximum likelihood decoder for the inner codes.
Advanced approaches for analysis and form finding of membrane structures with finite elements
(2018)
Part I deals with material modelling of woven fabric membranes. Due to their structure of crossed yarns embedded in coating, woven fabric membranes are characterised by a highly nonlinear stress-strain behaviour. In order to determine an accurate structural response of membrane structures, a suitable description of the material behaviour is required. A linear elastic orthotropic model approach, which is current practice, only allows a relative coarse approximation of the material behaviour. The present work focuses on two different material approaches: A first approach becomes evident by focusing on the meso-scale. The inhomogeneous, however periodic structure of woven fabrics motivates for microstructural modelling. An established microstructural model is considered and enhanced with regard to the coating stiffness. Secondly, an anisotropic hyperelastic material model for woven fabric membranes is considered. By performing inverse processes of parameter identification, fits of the two different material models w.r.t. measured data from a common biaxial test are shown. The results of the inversely parametrised material models are compared and discussed.
Part II presents an extended approach for a simultaneous form finding and cutting patterning computation of membrane structures. The approach is formulated as an optimisation problem in which both the geometries of the equilibrium and cutting patterning configuration are initially unknown. The design objectives are minimum deviations from prescribed stresses in warp and fill direction along with minimum shear deformation. The equilibrium equations are introduced into the optimisation problem as constraints. Additional design criteria can be formulated (for the geometry of seam lines etc.). Similar to the motivation for the Updated Reference Strategy [4] the described problem is singular in the tangent plane. In both the equilibrium and the cutting patterning configuration finite element nodes can move without changing stresses. Therefore, several approaches are presented to stabilise the algorithm. The overall result of the computation is a stressed equilibrium and an unstressed cutting patterning geometry. The interaction of both configurations is described in Total Lagrangian formulation.
The microstructural model, which is focused in Part I, is applied. Based on this approach, information about fibre orientation as well as the ending of fibres at cutting edges are available. As a result, more accurate results can be computed compared to simpler approaches commonly used in practice.
Sleep study can be used for detection of sleep quality and in general bed behaviors. These results can helpful for regulating sleep and recognizing different sleeping disorders of human. In comparison to the leading standard measuring system, which is Polysomnography (PSG), the system proposed in this work is a non-invasive sleep monitoring device. For continuous analysis or home use, the PSG or wearable Actigraphy devices tends to be uncomfortable. Besides, these methods not only decrease practicality due to the process of having to put them on, but they are also very expensive. The system proposed in this paper classifies respiration and body movement with only one type of sensor and also in a noninvasive way. The sensor used is a pressure sensor. This sensor is low cost and can be used for commercial proposes. The system was tested by carrying out an experiment that recorded the sleep process of a subject. These recordings showed excellent results in the classification of breathing rate and body movements.
This paper presents a bed system able to analyze a person’s movement, breathing and recognize the positions that the subject is lying on the bed during the night without any additional physical contact. The measurements are performed with sensors placed between the mattress and the bed-frame. An Intel Edison board was used as an endpoint that served as a communication node from the mesh network to external service. Two nodes and Intel Edison are attached to the bottom of the bed frame and they are connected to the sensors. First test results have indicated the potential of the proposed approach for the recognition of sleep positions with 83% of correct recognized positions.
The process of restoring our body and brain from fatigue is directly depend-ing on the quality of sleep. It can be determined from the report of the sleep study results. Classification of sleep stages is the first step of this study and this includes the measurement of biovital data and its further processing.
In this work, the sleep analysis system is based on a hardware sensor net, namely a grid of 24 pressure sensors, supporting sleep phase recognition. In comparison to the leading standard, which is polysomnography, the proposed approach is a non-invasive system. It recognises respiration and body move-ment with only one type of low-cost pressure sensors forming a mesh archi-tecture. The nodes implement as a series of pressure sensors connected to a low-power and performant microcontroller. All nodes are connected via a system wide bus with address arbitration. The embedded processor is the mesh network endpoint that enables network configuration, storing and pre-processing of the data, external data access and visualization.
The system was tested by executing experiments recording the sleep of different healthy young subjects. The results obtained have indicated the po-tential to detect breathing rate and body movement. A major difference of this system in comparison to other approaches is the innovative way to place the sensors under the mattress. This characteristic facilitates the continuous using of the system without any influence on the common sleep process.
Corporate venturing is one way for corporations to
introduce strategic renewal into their business portfolios, which is
imperative for ongoing success in innovation-driven industries.
Prior research finds that corporate ventures should be separated
from the mainstream business in loosely coupled sub-units, but
scholars continue to discuss how loose or tight the ventures should
be to balance exploration and exploitation. Hence, the antecedents
for successful venture management are yet to be fully explored and
our study contributes to this effort. The study shows that
corporate venture success is enhanced when corporate
management grants job and strategic autonomy to the venture
managers. This is further amplified when corporate management
simultaneously imposes an exploitative policy that forces venture
managers to prioritize extensions to and improvements of existing
competences and product-market offerings.
This paper focuses on the multivariable control of a drawing tower process. The nature of the process together with the differences in measurement noise levels that affect the variables to be controlled motivated the development of a new MPC algorithm. An extension of a multivariable predictive control algorithm with separated prediction horizons is proposed. The obtained experimental results show the usefulness of the proposed algorithm..