Refine
Year of publication
- 2015 (83) (remove)
Document Type
- Conference Proceeding (62)
- Article (8)
- Other Publications (8)
- Part of a Book (3)
- Doctoral Thesis (2)
Language
- English (83) (remove)
Has Fulltext
- no (83) (remove)
Keywords
- Algorithm (1)
- Autonomy (1)
- BCH codes (1)
- Bernstein coefficients (1)
- Bernstein polynomial (1)
- Bernstein polynomials (1)
- Biomechanics Laboratory (1)
- Body-movement (1)
- CONCATENATED codes (1)
- CONVOLUTION codes (1)
Institute
In biomechanics laboratories the ground reaction force time histories of the foot-fall of persons are usually measured using a force plate. The accelerations of the floor, in which the force plate is embedded, have to be limited, as they may influence the accuracy of the force measurements. For the numerical simulation of vibrations induced by humans in biomechanical laboratories, loading scenarios are defined. They include continuous motions of persons (walking, running) as well as jumps, typical for biomechanical investigations on athletes. The modeling of floors has to take into account the influence of floor screed in case of portable force plates. Criteria for the assessment of the measuring error provoked by floor vibrations are given. As an example a floor designed to accommodate a force platform in a biomechanical laboratory of the University Hospital in Tübingen, Germany, has been investi-gated for footfall induced vibrations. The numerical simulation by a finite element analysis has been validated by field measurements. As a result, the measuring error of the force plate installed in the laboratory is obtained for diverse scenarios.
IGA using subdivision-solids
(2015)
Bernstein polynomials on a simplex V are considered. The expansion of a given polynomial p into these polynomials provides bounds for range of p over V. Bounds for the range of a rational function over V can easily be obtained from the Bernstein expansions of the numerator and denominator polynomials of this function. In this paper it is shown that these bounds converge monotonically and linearly to the range of the rational function if the degree of the Bernstein expansion is elevated. If V is subdivided then the convergence is quadratic with respect to the maximum of the diameters of the subsimplices.
Tourist tracking
(2015)
This work investigates soft input decoding for generalized concatenated (GC) codes. The GC codes are constructed from inner nested binary Bose-Chaudhuri-Hocquenghem (BCH)codes and outer Reed-Solomon (RS) codes. In order to enable soft input decoding for the inner BCH block codes, a sequential stack decoding algorithm is used. Ordinary stack decoding of binary block codes requires the complete trellis of the code.
In this work a representation of the block codes based on the trellises of supercodes is proposed in order to reduce the memory requirements for the representation of the BCH codes. Results for the decoding performance of the overall GC code are presented.
Furthermore, an efficient hardware implementation of the GC decoder is proposed.
This paper proposes a pipelined decoder architecture for generalised concatenated (GC) codes. These codes are constructed from inner binary Bose-Chaudhuri-Hocquenghem (BCH) and outer Reed-Solomon codes. The decoding of the component codes is based on hard decision syndrome decoding algorithms. The concatenated code consists of several small BCH codes. This enables a hardware architecture where the decoding of the component codes is pipelined. A hardware implementation of a GC decoder is presented and the cell area, cycle counts as well as the timing constraints are investigated. The results are compared to a decoder for long BCH codes with similar error correction performance. In comparison, the pipelined GC decoder achieves a higher throughput and has lower area consumption.
Hot isostatic pressing (HIP) allows the production of complex components geometry. Generally, a high quality of the components is achieved due to the well managed composition of the metal powder and the non-isotropic properties. If a duplex stainless steel is produced, a heat treatment after the HIP-process is necessary to remove precipitations like carbides, nitrides and intermetallic phases. In a new process, the sintering step should be combined with the heat treatment. In this case a high cooling rate is necessary to avoid precipitations in duplex stainless steels. In this work, the influence of the HIP-temperature and the wall thickness on corrosion resistance, microstructure and impact strength were investigated. The results should help to optimize the process parameters like temperature and cooling rate. For the investigation, two HIP-temperatures were tested in a classical HIP-process step with a defined cooling rate. An additional heat treatment was not conducted. The specimens were cut from different sectors of the HIP-block. For investigation of the corrosion resistance, the critical pitting temperature was determined with electrochemical method according to EN ISO 17864. An impact test was used to determine the impact transition temperature. Metallographic investigations show the microstructure in the different sectors of the HIP-block.