Refine
Year of publication
- 2017 (94) (remove)
Document Type
- Conference Proceeding (94) (remove)
Keywords
- Actuators (1)
- Ambidexterity (1)
- Automation (1)
- B-spline activation function (1)
- Barriers to Business Model Innovation (1)
- Business Model Innovation (1)
- Business Plan (1)
- Business model (1)
- Business plan (1)
- Cables (1)
Institute
The binary asymmetric channel (BAC) is a model for the error characterization of multi-level cell (MLC) flash memories. This contribution presents a joint channel and source coding approach improving the reliability of MLC flash memories. The objective of the data compression algorithm is to reduce the amount of user data such that the redundancy of the error correction coding can be increased in order to improve the reliability of the data storage system. Moreover, data compression can be utilized to exploit the asymmetry of the channel to reduce the error probability. With MLC flash memories data compression has to be performed on block level considering short data blocks. We present a coding scheme suitable for blocks of 1 kilobyte of data.
One major realm of Condition Based Maintenance is finding features that reflect the current health state of the asset or component under observation. Most of the existing approaches are accompanied with high computational costs during the different feature processing phases making them infeasible in a real-world scenario. In this paper a feature generation method is evaluated compensating for two problems: (1) storing and handling large amounts of data and (2) computational complexity. Both aforementioned problems are existent e.g. when electromagnetic solenoids are artificially aged and health indicators have to be extracted or when multiple identical solenoids have to be monitored. To overcome those problems, Compressed Sensing (CS), a new research field that keeps constantly emerging into new applications, is employed. CS is a data compression technique allowing original signal reconstruction with far fewer samples than Shannon-Nyquist dictates, when some criteria are met. By applying this method to measured solenoid coil current, raw data vectors can be reduced to a way smaller set of samples that yet contain enough information for proper reconstruction. The obtained CS vector is also assumed to contain enough relevant information about solenoid degradation and faults, allowing CS samples to be used as input to fault detection or remaining useful life estimation routines. The paper gives some results demonstrating compression and reconstruction of coil current measurements and outlines the application of CS samples as condition monitoring data by determining deterioration and fault related features. Nevertheless, some unresolved issues regarding information loss during the compression stage, the design of the compression method itself and its influence on diagnostic/prognostic methods exist.
This work proposes a decoder implementation for high-rate generalized concatenated (GC) codes. The proposed codes are well suited for error correction in flash memories for high reliability data storage. The GC codes are constructed from inner extended binary Bose-Chaudhuri-Hocquenghem (BCH) codes and outer Reed-Solomon (RS) codes. The extended BCH codes enable high-rate GC codes. Moreover, the decoder can take advantage of soft information. For the first three levels of inner codes we propose an optional Chase soft decoder. In this work, the code construction is explained and a decoder architecture is presented. Furthermore, area and throughput results are discussed.
Observer-based self sensing for digital (on–off) single-coil solenoid valves is investigated. Self sensing refers to the case where merely the driving signals used to energize the actuator (voltage and coil current) are available to obtain estimates of both the position and velocity. A novel observer approach for estimating the position and velocity from the driving signals is presented, where the dynamics of the mechanical subsystem can be neglected in the model. Both the effect of eddy currents and saturation effects are taken into account in the observer model. Practical experimental results are shown and the new method is compared with a full-order sliding mode observer.
Sleep quality and in general, behavior in bed can be detected using a sleep state analysis. These results can help a subject to regulate sleep and recognize different sleeping disorders. In this work, a sensor grid for pressure and movement detection supporting sleep phase analysis is proposed. In comparison to the leading standard measuring system, which is Polysomnography (PSG), the system proposed in this project is a non-invasive sleep monitoring device. For continuous analysis or home use, the PSG or wearable Actigraphy devices tends to be uncomfortable. Besides this fact, they are also very expensive. The system represented in this work classifies respiration and body movement with only one type of sensor and also in a non-invasive way. The sensor used is a pressure sensor. This sensor is low cost and can be used for commercial proposes. The system was tested by carrying out an experiment that recorded the sleep process of a subject. These recordings showed the potential for classification of breathing rate and body movements. Although previous researches show the use of pressure sensors in recognizing posture and breathing, they have been mostly used by positioning the sensors between the mattress and bedsheet. This project however, shows an innovative way to position the sensors under the mattress.
Successful project management (PM), as one of the most important key competences in the western-oriented working world, is mainly influenced by experience and social skills. As a direct impact on PM training, the degree of practice and reality is crucial for the application of lessons learned in a challenging everyday work life. This work presents a recursive approach that adapts well-known principles of PM itself for PM training. Over three years, we have developed a concept and an integrated software system that support our PM university courses. Stepwise, it transfers theoretical PM knowledge into realistic project phases by automatically adjusting to the individual learning progress. Our study reveals predictors such as degrees of collaboration or weekend work as vital aspects in the PM training progress. The chosen granularity of project phases with variances in different dimensions makes our model a canonical incarnation of seamless learning.
Business models (BM) are the logic of a firm on how to create, deliver and capture value. Business model innovation (BMI) is essential to organisations for keeping competitive advantage. However, the existence of barriers to BMI can impact the success of a corporate strategic alignment. Previous research has examined the internal barriers to business model innovation, however there is a lack of research on the potential external barriers that could potentially inhibit business model innovation. Drawn from an in-depth case study in a German medium size engineering company in the equestrian sports industry, we explore both internal and external barriers to business model innovation. BMI is defined as any change in one or more of the nine building blocks of the Business Model Canvas; customer segment, value propositions, channels, customer relation, revenue streams, key resources, key activities, key partners, cost structure [1]. Our results show that barriers to business model innovation can be overcome by the deployment of organisational learning mechanisms and the development of an open network capability.
Validity of the business model is a key indicator for buying into ventures in the early-stage. Business models of early-stage ventures decrease in validity when developing the business over the progressing stages of the business life-cycle. By doing so, the ventures are validating their business model when building transaction relationships to the surrounding value network. In prior research, we developed a research design based on existing business innovation proposals (onepager, pitch decks, business plans) that is assumed to evaluate the status of business model validation. The core hypothesis of the research design is that transaction relations represent a strong anchor between the business model and the business reality, thus providing information on the business model validity. In this research, we test this hypothesis by designing and analyzing a survey that was directed to founders taking part in a business plan competition. We compared the relationships described in the submitted business plans to the relations explicitely stated in the follow-up questionnaire. We identified that the described relations to customers, investors, and people (human resources) match the relationships expressed in questionnaires quite well. A significant disagreement, however, exists in the relationships to suppliers. We conclude that there is still a theoretical and empirical gap that leads to disagreement between business plans and reality in the group of suppliers.
Corporate entrepreneurship (CE) supports the strategic renewal of established companies. Corporate venturing represents one key concept of CE that supports companies to strengthen their innovation capabilities. For the successful implementation of corporate ventures dual structures are recommended. The question, how the interface should be designed, plays a crucial role. Although it seems to be an important factor, this aspect requires further attention. One relevant element of the interface design are the different roles of the individuals that are interacting within the interface. This study is based on nine interviews that are representing six internal corporate ventures within one large German corporate from the ICT sector. The results that were mirrored with short case studies of 25 additional companies of the data sample, contribute to a better understanding of the interface design by adding insights about roles in corporate entrepreneurship. This deeper understanding about roles allows to draw conclusions on the interface design from a structural point of view.
As a result of increasing needs and shrinking resources, aquaculture is gaining progressively significance in the recent years. Ecological issues such as negative effects on the ecological system due to the high fish density in the farms, the use of copper as antifouling strategy etc. are very present, particularly regarding the increasing number of fish going to be produced in farms in the future. Current trends focus on larger farms operated offshore. To make these farms working safe and economical, reliability has to be improved and maintenance costs need to be reduced. Also, alternatives with higher mechanical strength compared to current textile net materials as well as common metal wires might be necessary. In the last years, a new net system made of high strength duplex stainless steel wires with environmentally friendly antifouling properties suitable for offshore applications was developed. The first nets are operating for one year now as predator protection (i.e. seals) for fish farms and show a good performance in cleaning capability and predator protection. But in the real usage, some corrosion effects in the contact points of the net made of duplex stainless steel 1.4362 occur which were not observed in preliminary tests in laboratory and at different test sites around the world. These corrosion effects endanger the sustainable success of the net system. In this work, the observed corrosion effects are investigated. A laboratory test, which simulates the movement in the contact points of the net, was developed. Two pieces of wire are bent in the middle and get stucked into each other. One wire is fixed at both ends and the second wire is fixed on one end. On the other end, a circular movement with 1-2 rps and a 1 cm displacement is applied. The movement generates friction between the wires and the passive layer will be locally damaged. When the movement stops, a repassivation starts. The passivity breakdown and the repassivation were measured with electrochemical techniques. During the friction phase, when the surface will be activated, the open circuit potential breaks down. When the friction stops, the OCP increases. Between the movement phases, measurements of critical pitting potential were done. Thereby the quality of repassivation was investigated. The tests were done in a 3% sodium chloride solution. Different temperatures were tested as well as the influence of air saturation and low oxygen content.
Deep 3D
(2017)
Design of tension components
(2017)
The paper gives an introduction as well as background information on proposed changes and amendments in EN 1993-1-11 “Design of structures with tension components”, implemented during the ongoing revision. Due to some deficits in the currently applicable standard this revision is not only limited to some restructuring and editorial changes, but includes also major technical changes in the following fields: safety concept and structural analysis, actions and loads, robustness and rep-arability, design of tension components and design of clamps and saddles.
We present an analysis of how to determine security requirements for software that controls routing decisions in the distribution of discrete physical goods. Requirements are derived from stakeholder interests and threat scenarios. Three deployment scenarios are discussed: cloud and hybrid deployment as well as on-premise installation for legacy sites.
Poster
Durch die Einführung cyber-physischer Systeme in der Produktion ändern sich Arbeitsbedingungen und Prozesse sowie Geschäftsmodelle. In der Praxis kann eine wachsende Diskrepanz zwischen großen und kleinen bzw. mittelständischen Unternehmen beobachtet werden. Um diese Diskrepanz zu überbrücken, wird eine Modellfabrik vorgestellt, die Unternehmen eine Plattform zum Probieren bietet, die Möglichkeit zur Ausbildung von Studenten und Mitarbeitern schafft und Beratungsangebote bereithält. Am Beispiel einer dezentralisierten Demonstrationsfabrik wird ein hochintegriertes, offenes und standardisiertes Automatisierungskonzept vom Shopfloor bis hin zu einem Business Ecosystem präsentiert. Eine Suchmaschine dient als Basis für ein Fertigungsmanagementsystem (MES). Die Informationsverarbeitung erfolgt nach dem Pull-Prinzip, welches bei einem nach Lean optimierten Prozess bereits Anwendung findet.
Standardmäßig werden zur Modellierung magnetischer Systeme für regelungstechnische Anwendungen oder im Bereich der Diagnose und Prognose konzentriert parametrische Modelle verwendet. Falls eine hohe Qualität der Prozessabbildung erforderlich ist, z.B. um Wirbelströme oder Sättigung geeignet zu berücksichtigen, nehmen diese Modelle schnell relativ hohe Ordnungen an. Es ist seit einiger Zeit bekannt, dass verteilparametrische Systeme, die z.B. (Feld-)Diffusionsprozesse beinhalten, durch niederdimensionale Modelle mit nicht ganzzahligen Ableitungen, so genannte fraktionale Modelle, sehr gut abgebildet werden können. Im Bereich der magnetischen Aktuatoren wurden diese vor rund 10 Jahren zum ersten Mal untersucht. Seitdem wird auf diesem Gebiet in verschiedenen Arbeitsgruppen geforscht. Während im Frequenzbereich die Handhabung fraktionaler Systeme einfach ist, sind Anwendungen im Zeitbereich bisher insbesondere bei zeitkritischen Anwendungen kaum anzutreffen. Der Beitrag stellt die prinzipielle Idee dar und zeigt Möglichkeiten zum Einsatz dieser Verfahren im Bereich magnetischer Aktoren auf. In einer konkreten Anwendung wird in Simulation und Experiment demonstriert, wie mit Hilfe dieser Modelle Zustandsschätzung in Magnetaktuatoren erfolgen kann und welche Vorteile sich dadurch ergeben.
Was in Kommunen im benachbarten Ausland, bspw. der Schweiz, Österreich oder den Niederlanden offenbar seit vielen Jahren Stand der Technik ist, ist auf Deutschlands Kommunalstraßen eine „Sonderbauweise“: Betonfahrbahnen. Obwohl, gerade in den neuen Bundesländern diese Bauweise häufig zum Einsatz kam, wird sie heute auf größeren Flächen wie gesamte Straßenzüge, bspw. in Wohngebieten, kaum noch angewendet (Bild 1). Die Gründe liegen offenbar in den schlechten Erfahrungen hinsichtlich einer komfortablen Nutzungsdauer sowie der Notwendigkeit, einen „leichteren“ Zugriff auf die unter der Straßenoberfläche liegenden Ver- und Entsorgungseinrichtungen zu haben. Infolge vermehrt auftretender Schäden wie Spurrinnen, Verdrückungen und weiteren Schäden werden hochbelastete Verkehrsflächen wie Bushaltestellen, Busspuren und Kreisverkehre immer häufiger anstatt in Asphalt- oder Pflaster in Betonbauweise ausgeführt. Die Gründe für die Vernachlässigung der Betonbauweise im kommunalen Umfeld liegen neben einem geringen Erfahrungsschatz sicherlich auch in einer aufwändigeren Planung, höheren Ausführungskosten, einem komplexeren Einbau, gerade in Zusammenhang mit Einbauten, Instandhaltungsmaßnahmen und Maßnahmen Dritter an den Ver- und Entsorgungseinrichtungen. Offen ist auch der Nachweis, dass die Betonbauweise im Lebenszyklus wirtschaftlicher als beispielsweise die Asphaltbauweise ist. Die Thematik „Einsatz von Betonflächen in Kommunen“ ist sehr umfangreich und weitläufig und lässt sich mit einem Vortrag generell nicht behandeln. Mit nachfolgenden Ausführungen soll demnach grundsätzlich auf die Belange der Planung, dem Bau und der Wirtschaftlichkeit kommunaler Verkehrsflächen in Betonbauweise eingegangen werden. Es können leider nicht alle Besonderheiten und Einzelheiten wie Baustoffe (Glasfaser) Berücksichtigung finden. Ziel des Vortrages ist, generelle Möglichkeiten hinsichtlich dem Einsatz von Betonflächen im kommunalen Bereich aufzuzeigen. Besonderer Dank gilt dem Straßenbauamt Böblingen sowie Herrn Baudirektor Andreas Klein, dessen persönliche Erfahrungen hier einfließen durften.
The electrochemical behavior for different surface conditions and different degrees of deformation of metastable austenitic stainless steel AISI 304 UNS S30400 were studied using critical pitting potential and electrochemical noise measurements. The influence on corrosion resistance by using different abrasives (silicon carbide and corundum) for surface finish by grinding is illustrated. For the characterization of local defects and surface topography, scanning electron microscopy (SEM) and tactile measurements were used. An inverse correlation between occurrence of local defects on the surface and critical pitting potential was found by using image processing. Therefore, gray scale values of different surfaces were compared. The influence of mass content of α'-martensite on the corrosion resistance is shown by comparing different qualities of surface finish. For smooth machined surfaces it can be shown that an increasing numbers of strain induced martensite is decreasing the corrosion resistance lightly. For low abrasive machining an inverse correlation between the critical pitting potential and surface roughness is given. However, for higher abrasive machining parameters, this correlation could not be found.
Durch Beanspruchungen bei der Fertigung oder in der Anwendung können metastabile austenitische Stähle eine Phasenumwandlung von ?- Austenit zu ?‘-Martensit durchlaufen. Verbunden damit sind Eigenschaftsänderungen, welche sich signifikant auf das Werkstoffverhalten unter mechanischer, tribologischer oder korrosiver Belastung auswirken können.
Um möglichen negativen Auswirkungen wie ungewollte Magnetisierbarkeit oder Beeinflussung von Fertigungsparameter sowie Korrosionseigenschaften zu unterbinden muss die martensitische Phase zunächst erfasst und quantifiziert werden.
Für diese Aufgabe stehen neben den bekannten und kostenintensiven Verfahren wie EBSD und XRD für die praxisnahe Anwendung das magneto-induktive Messverfahren und verschiedene Ätzmethoden zur Verfügung.
Anhand von Applikationen aus Anwendung, Fertigung und Forschung werden die Wirkweisen, Vorteile und Grenzen verschiedener Ätzverfahren und dem magneto-induktiv messenden FERITSCOPE® MP30 aufgezeigt. Ebenso werden ergänzende Methoden bzw. Techniken zur Validation der Verfahren diskutiert und erläutert.
Error correction coding based on soft-input decoding can significantly improve the reliability of flash memories. Such soft-input decoding algorithms require reliability information about the state of the memory cell. This work proposes a channel model for soft-input decoding that considers the asymmetric error characteristic of multi-level cell (MLC) and triple-level cell (TLC) memories. Based on this model, an estimation method for the channel state information is devised which avoids additional pilot data for channel estimation. Furthermore, the proposed method supports page-wise read operations.
In the reverse engineering process one has to classify parts of point clouds with the correct type of geometric primitive. Features based on different geometric properties like point relations, normals, and curvature information can be used, to train classifiers like Support Vector Machines (SVM). These geometric features are estimated in the local neighborhood of a point of the point cloud. The multitude of different features makes an in-depth comparison necessary. In this work we evaluate 23 features for the classification of geometric primitives in point clouds. Their performance is evaluated on SVMs when used to classify geometric primitives in simulated and real laser scanned point clouds. We also introduce a normalization of point cloud density to improve classification generalization.
Growth is a key indicator of the prosperity of an economy. In today's Germany the " Gründerzeit " still describes a period of enormous economic growth. Factors that lead to growth haven't been investigated in the context of the different life cycle stages of early-stage technology ventures so far. This paper proposes a model of early-stage ventures' growth based on factors. From a theoretical angle, we look at the business from the market-based view (MBV) and the resource-based view (RBV) on strategy in the longitudinal perspective of the business life cycle. With this view we get to know what are the stage specific needs and processes of new technology based ventures in order to provide appropriate support. We tested different potential growth indicators for the model with a questionnaire-based survey which was answered by 68 high-tech entrepreneurs. The results suggest that growth factors are stage specific in their relevance. While leading to growth in one stage, certain factors evince no or even negative influence on growth in other stages. Moreover, RBV factors as seen more relevant for the growth than the MBV factors. Further research requires a large and representative population to validate the results. Keywords:-growth factors, early-stage ventures, market-based view, resources based view.
I4 Production
(2017)
In diesem Beitrag wird die Hardware-Implementierung eines Datenkompressionsverfahrens auf einem FPGA vorgestellt. Das Verfahren wurde speziell für Kompression kurzer Datenblöcke in Flash-Speichern entwickelt. Dabei werden Quelldaten mithilfe eines Encoders komprimiert und mit einem Decoder verlustlos dekomprimiert. Durch die Reduktion der Datenrate kann in Flash-Speichern die Übertragungsdauer zum Lesen und Schreiben reduziert werden. Ebenso ist eine Kompression von Nutzdaten sinnvoll, um zusätzliche Redundanzen für einen Fehlerschutz einfügen zu können, ohne den Gesamtspeicherplatzbedarf zu erhöhen.
InBetween
(2017)
Industry 4.0
(2017)